Dave Poske Catalog 2025

REAR END

ORDER ONLINE @ www.poske.com

OCTANE 3 STAGE TORQUE LINK PULL BAR 3 stage torque link that allows the

ADJUSTABLE RAISED SHOCK MOUNT

PULLBARS Uses the Outlaw bearing to offer

the smoothest motion in a standard pull bar.This design pull bar has relocated the brake biscuit to the head end of the bar.This allows you to preload the spring without going through the rubber biscuit. Dirt seals on each end of the bearing help keep this a

traction and brake shaft to opporate seperate.This is

Weld-On For 1 1/2" Tube WEH WM446-1-1500................Ea

2 STAGE POLY POSI-STOP TORQUE LINK The Posi-Stop Rate Progression Torque Links with Adjustable Spring Bushing Has the ability to run a very soft spring bushing for good initial traction & better restarts, with a harder spring bushing to maintain traction out of the corner; A Positive Travel Stop prevents the soft spring bushing from being over compressed; Two Stage Torque Link has an additional adjustable travel stop which “Locks Up” the torque link after a turn allows the brake bushing to be tuned with out affecting the acceration tuning. Has a 3/4" chrome plated shaft with sealed bearings will allow for bind free use. Has replaceable bushings that allow for more tune-ability while you search for the drive and braking that other torque links won't allow for. OCT 01-26500 ............................................. Pull Bar OCT 01-26501 ......... Shaft for 01-26500 10.935” pre-set amount of spring bushing compression so engine torque is not wasted in compressing the bushings; The progression of the spring rate can be quickly tailored without removing the torque link from the car. Decreasing the compression of the soft bushing has the effect of increasing spring rate while increasing the travel has the effect of decreasing the spring rate; Isolated traction and brake shafts so engine and brake spring bushings operate independently. Corner entry & exit can be tuned separately.The brake bushing works sooner because it’s not pre-loaded with traction bushing pre-load.The car turns better in the middle of the corner and comes off the bars smoother because there’s less wrap-up; Built-in travel indicator to measure compression travel. Feature heavy duty stand off rods, sealed bushings and a 3/4” chrome plated shaft. OCT 01-26550 ..................................... Torque Link

BSB SHOCK MOUNTS Aluminum Swivel.Turns Shock Eye Parellel with Mount. 5", 6" and 7" Drop. Fits BSB and GRT Cages BSB 4210-9 .........................................Shock Mount

maintenance free pull bar. Special Features Include: Outlaw Bearing, a Travel Indicator, Hardened Shaft, Double Lip Dirt Seals. Rod ends are included. BSB 7600 .........................................................23-1/2" BSB 7600-8 ................................ Replacement Shaft BSB 7640...................Red Brake Bushing for 7600 BSB 7600-9 ...........Replacement Shaft - 5/8” Zinc Yellow Coated

7550-7

LEFT REAR CHAIN LIMITER

7550-4

Steel 90° Swivel. Mounts to Steel Birdcages Allows Movement of Shock Eye. Prevents Breaking Eye Off

SINGLE SIDED ARCFRAME SLIDER Single Sided slotted 2" Frame Slider BSB 7054-20 ......................................... Frame Slider BSB 7550-4 ................................. Repl Shock Clevis BSB 7550-7 ................................. Repl Shock Clevis

ROC MRRCLRLA-2020.......................Bushing Style

CHAIN MOUNT FOR AXLETUBE 2 Bolt Chain Mount for Axle Tube OCT 01-26100 ......... Single Shear OCT 01-26105 .......Double Shear

PROGRESSIVE PULL BAR SPRING Eibach 6-3/4” progressive pull bar springs, 5” O.D. EIB 0675-500-2000 ........................... 500# - 2000#

STEEL FRAME SLIDER

2 hole bracket. Available for both 1.5" & 2" tubing.

OCT 01-26030 ..........................1.5" Square Tubing OCT 01-26040 ............................. 2" Square Tubing

PROGRESSIVE SPRINGS

UBMOUNTS

HYP 175500 ........... 2.5” ID 175#-500# HYP 600-1200 . 5” x 7” x 600#-1200#

OUTERWEARS PULL BAR COVER 46-1825 URB 46-0138................................Lift Bar Stabilizer URB 46-1825.......................Panhard Mount 1-1/2" URB 46-1870................. Panhard Mnt 1.5” Square

UB BOLT-ON DROP SHOCK MOUNT BRACKETS

LARGE POLY PULL BAR BUSHINGS HELPER SPRING SWI H025-135-0008 ..........2.5” X 5.3” Tall PROGRESSIVE TORQUE-LINK (Pull Bar) Spring SWI 067-500-600-2000 . 5” X 6.75” X 600/2000 S P

Bolt-on Drop Shock Mounts for 3" Axle tubes. URB 35-3340..................................... 5" Shock Drop

WELD UP SOLID PULL BARKIT

Available in four different rates, 55, 60, 65 and 75 durometer readings.

4 Foot of 1.25” X .095”Tubing, 1 LH 3/4”Weld in Tubing End, 1 RH 3/4”Weld in Tubing End (with Heim has 1 each of LH & RH Jam nut) OCT 01-26025 .................................. Kit No Heims OCT 01-26026 ................................ Kit with Heims

Shock Wears are an inexpensive way to keep your pullbars clean and looking good. 15 3/4" in circumference and 7" long. OUT 30-2608-01 ............................ Pull Bar Cover

OCT 01-26555 ............................. Orange 55 Duro OCT 01-26560 ............................... Purple 60 Duro OCT 01-26565 ............................... Yellow 65 Duro OCT 01-26580 ................................... Blue 75 Duro

33

WARNING: Some products can expose you to chemicals which are known to the state of California to cause cancer and birth defects or other reproductive harm. www.P65Warnings.ca.gov