Dave Poske Catalog 2023

LIFT ARM PLATES & PULL BARS

ORDER ONLINE @ www.poske.com

OCTANE 6TH COIL ASSEMBLY

OCTANE 3 STAGE TORQUE LINK PULL BAR 3 stage torque link that allows the

BSBPULL BARS

Uses the Outlaw bearing to offer the smoothest motion in a standard pull bar. This design pull bar has relocated the brake biscuit to the head end of the bar.This allows you to preload the spring without going through the rubber biscuit. Dirt seals on each end of the bearing help keep this a maintenance free pull bar. Special Features Include: Outlaw Bearing, a Travel Indicator, Hardened Shaft, Double Lip Dirt Seals. Rod ends are included. BSB 7600 .........................................................23-1/2" BSB 7600-8 ................................ Replacement Shaft BSB 7640...................Red Brake Bushing for 7600 BSB 7600-9 ...........Replacement Shaft - 5/8” Zinc Yellow Coated

traction and brake shaft to opporate seperate.This is turn

BSB 6TH COIL ASSEMBLY OCT 01-27000 ......................... Coil Assembly OCT 01-27001 .............................Mount Only

allows the brake bushing to be tuned with out affecting the acceration tuning. Has a 3/4" chrome plated shaft with sealed bearings will allow for bind free use. Has replaceable bushings that allow for more tune ability while you search for the drive and braking that other torque links won't allow for. OCTANE 2 STAGE POLY POSI-STOP TORQUE LINK Our new Posi-Stop Rate Progression Torque Links with Adjustable Spring Bushing Travel Stops are the latest leap forward in torque link technology. Ability to run a very soft spring bushing for good initial traction & better restarts, combined with a harder spring bushing to maintain traction

Made from steel and fi ts short 5” springs. Smoother suspension travel allows it to swivel in four directions. Keeps even pressure on chain BSB 7066 ............................................ Coil Assembly

OCT 01-26500 ............................................. Pull Bar OCT 01-26501 ......... Shaft for 01-26500 10.935”

LEFT REAR CHAIN LIMITER

OCTANE J-BAR THREADSERT

Pictured with 3/4" RH Heim and Jam Nut. Heim is sold separately OCT 01-25001 .............................Threadsert Only

ROC MRRCLRLA-2020.................... Bushing Style

OCTANE LIFT BAR STABLIZERS 2 Bolt Rear End Chain Mount

ROCKET LIFT BARPLATES

out of the corner; A Positive Travel Stop prevents the soft spring

bushing from being over-compressed greatly improving spring bushing life; Two Stage Torque Link has an additional adjustable travel stop which “Locks Up” the torque link after a pre-set amount of spring bushing compression so engine torque is not wasted in compressing the bushings; The progression of the spring rate can be quickly tailored to track conditions without removing the torque link from the car. Decreasing the compression of the soft bushing has the effect of increasing spring rate while increasing the travel has the effect of decreasing the spring rate; Isolated traction and brake shafts so engine and brake spring bushings operate independently. Corner entry & exit can be tuned separately. The brake bushing works sooner because it’s not pre loaded with traction bushing pre-load.The car turns better in the middle of the corner and comes off the bars smoother because there’s less wrap-up; Built-in travel indicator to measure compression travel. Feature heavy duty stand off rods, sealed bushings and a 3/4” chrome plated shaft. OCT 01-26550 ..................................... Torque Link OUTERWEARS PULL BAR COVER

OCTANE REPLACEMENT BISCUIT BUSHINGS Replacement for Lightning Modi fi eds OCT 01-24011 .... Bushings OCT 01-26100 ......Single Shear OCT 01-26105 ...Double Shear

Both Plates (Pair) are Required. ROC PC3009-1 .............................. Lower Plate ea. ROC PC831121S ........................... Upper Plate ea.

OCTANE 1 PIECE DESIGN LIFT ARMPLATE More durable than 2-piece design. OCT 01-26015 .........1-Piece

OCTANE 2.25” TORQUE LINK BUSHINGS Available in three different rates, 60, 75 and 87 durometer readings. OCT 01-26506 .............................. Purple 60 Duro OCT 01-26507 .............................. Yellow 75 Duro OCT 01-26508 ................................... Red 87 Duro

OCTANE LARGE POLY PULL BAR BUSHINGS

EIBACH PULL BAR SPRING

Available in four different rates, 55, 60, 65 and 75 durometer readings. OCT 01-26555 ............................ Orange 55 Duro OCT 01-26560 .............................. Purple 60 Duro OCT 01-26565 .............................. Yellow 65 Duro OCT 01-26580 .................................. Blue 75 Duro

Eibach 6-3/4” progressive pull bar springs, 5” O.D. EIB 0675-500-2000 .....500# - 2000# Progressive

OCTANE WELD UP SOLID PULL BAR KIT

HYPERCO PROGRESSIVE SPRINGS

4 Foot of 1.25” X .095”Tubing, 1 Left Hand 3/4” Weld in Tubing End, 1 Right Hand 3/4”Weld in Tubing End (with Heim has 1 each of LH & RH Jam nut and Moly Heim) OCT 01-26025 .................................. Kit No Heims OCT 01-26026 ................................ Kit with Heims

Shock Wears are an inexpensive way to keep your pullbars clean and looking good. 15 3/4" in circumference and 7" long. OUT 30-2608-01 ............................ Pull Bar Cover

HYP 175500 ...2.5” ID 175#-500# HYP 600-1200 ................. 5” x 7” x 600#-1200#

37

WARNING: Some products can expose you to chemicals which are known to the state of California to cause cancer and birth defects or other reproductive harm. www.P65Warnings.ca.gov