2025-26 Total Wheel Alignment Sourcebook

Applications U CONVERSION TABLE – Toe Readings Inches Degrees

BOLD PART NUMBER INDICATES PREFERRED CORRECTION METHOD • WB = Check www.specprod.com for more information FOOTNOTES:

Metric MM Minutes of Degrees

.03 (1/32) .06 (1/16) .09 (3/32) .12 (1/8) .16 (5/32) .19 (3/16) .22 (7/32) .25 (1/4) .28 (9/32) .31 (5/16) .34 (11/32) .37 (3/8) .41 (13/32) .44 (7/16) .47 (15/32) .50 (1/2) .53 (17/32) .56 (9/16) .59 (19/32) .62 (5/8) .66 (21/32) .69 (11/16) .72 (23/32) .75 (3/4)

.06° (1/16°) .13° (1/8°) .19° (3/16°) .25° (1/4°) .31° (5/16°) .38° (3/8°) .44° (7/16°) .50° (1/2°) .56° (9/16°) .63° (5/8°) .69° (11/16°) .75° (3/4°) .81° (13/16°) .88° (5/8°) .94° (15/16°) 1.06° (1-1/16°) 1.13° (1-1/8°) 1.19° (1-3/16°) 1.25° (1-1/4°) 1.31° (1-5/16°) 1.38° (1-3/8°) 1.44° (1-7/16°) 1.50° (1-1/2°) 1.00° (1°)

0.8 1.6 2.4 3.2 4.0 4.8 5.6 6.4 7.1 7.9 8.7 9.5

3.75’ 7.50’ 11.25’ 15.00’ 18.75’ 22.50’ 26.25’ 30.00’ 33.75’ 37.50’ 41.25’ 45.00’ 48.75’ 52.50’ 56.25’ 60.00’

Labor times have been removed from the Sourcebook. SPC recommends consulting a Labor Time Guide for the Remove and Replace labor time for the appropriate part. Please review the SPC product installation instructions for any additional time required such as grinding. Add time as needed for the additional adjustments allowed. Always pre-check the vehicle for corrosion or modifications which might a ff ect installation time. N/A = No Available Adjuster • OEMA = Original Equipment Manufacturer Adjustment • ( * ) = Series P/N, see page for correct size (1) CAUTION: Check for caliper to rotor clearance with disc brakes. Use spacer set 75970 as necessary to keep caliper centered on rotor (2) All EXCEPT RWD 1500 • (3) Honda S2000 Ball Joint - Rear Application - Only for 17" rims or larger • (4) Check Bolt Length BEFORE Cutting Hole (6) LH Tie Rod Adjusting Sleeve Replacement • (7) Bolts, 73415, (pg. 115) are necessary for changes greater than 3/4° (8) Recommended for vehicles lowered more than 1.5" • (9) Will not work on 1988-89 models with welded-in ball joint (10) M3 Only, caster will decrease by 2 degrees • (11) Pinion Angle Adj. Part No. 82370 (pg. 122) • (12) Limited camber range of +/-1.0° (13) Center stock camber and toe adjusters before calculating shim change • (14) 69330 included w/69300 or 69400 • (15) Not for use w/disc brakes (16) Can be used for Caster or Pinion Angle • (17) Footnotes 1 and 13 • (18) Preferred • (19) Rear Pinion Angle • (20) Except Sti (21) Series P/N, Not for use with ABS• (22) Lower Arm 69400 • (23) Except Type R Lower Arm • (24) Rear Wheel Drive Only • (25) 92-96Only (26) 92-98 Only • (27) C10 and C15 • (28) Footnote 1, include the next part number • (29) Include the next part number • (30) With 10mm Bolt (31) With 12mm Bolt • (32) All Except AMG models • (33) 1988-91 1500 - 43mm Bushings Only • ( 34) Models equipped with taller hydraulic bushings must be pressed out and reused from the original control arm or the 72360 trailing link can be used if applicable • (35) Except stamped sheet metal upper control arms • (36) Without Front Ride Height Sensor • ( SW ) Station Wagon • ( L ) Lower Stock Replacement Part - This part matches the OE Part • Replacement Part - This part fits like an OE part, but improves on the OE part’s construction  Thrust Plate available for this vehicle - for more information see page 83

10.3 11.1 11.9 12.7 13.5 14.3 15.1 15.9 16.7 17.5 18.3 19.0

1° 3.75’ 1° 7.50’ 1° 11.25’ 1° 15.00’ 1° 18.75’ 1° 22.50’ 1° 26.50’ 1° 30.00’

DOMESTIC MODEL YEAR ID Letter/Number shown in 10th digit of V.I.N. tag.

YEAR DESIGNATION 1981 ......B 1982 ......C 1983 ......D 1984 ......E 1985 ......F 1986 ......G 1987 ......H 1988 ......J 1989 ......K 1990 ......L 1991 ..... M 1992 ......N 1993 ......P 1994 ......R 1995 ......S

YEAR DESIGNATION 2011 ......B 2012 ......C 2013 ......D 2014 ......E 2015 ......F 2016 ......G 2017 ......H 2018 ......J 2019 ......K 2020 ......L 2021 ..... M 2022 ......N 2023 ......O 2024 ......P 2025 ......Q

YEAR DESIGNATION 1996 ......T 1997 ......V 1998 ..... W 1999 ......X 2000 ......Y 2001 ......1 2002 ......2 2003 ......3 2004 ......4 2005 ......5 2006 ......6 2007 ......7 2008 ......8 2009 ......9 2010 ......A

Available for:

Android

Meet Specialty Products’ Alignment A AlignGuide ™ AlignGuide™ provides manufacturers’ alignmen specifications for makes and models since 1985 as well as information on service parts that are available to correct alignment problems. nt 5

App

Scan for more information

With AlignGuide, you will be able to enter a vehicle’s VIN, enter the license plate ID, or pull down the year, make & model to get the information you need to diagnose and correct an alignment problem and many suspension issues. Once your vehicle and preferred specifications have been identified, you can quickly see illustrations of alignment adjustment methods and service parts to install. See page 181 for more details.

Call for your nearest distributor, product info or www.specprod.com 1-800-525-6505 Technical Assistance • In the USA and Canada

68