2025-26 Total Wheel Alignment Sourcebook

Parts 71500 SERIES

VW/AUDI REAR SHIMS With these shims you can correct rear camber and toe on newer Volkswagens and Audis. By combining the shims (two may be used on each wheel) you can get ±.50° to ±1.0° camber change and up to ±.50° toe change. Our wrench (# 87530 ) is a must when in stalling these shims. It allows you to remove the

Rear Adjustment range: Camber ±.50° to ±1.00°/ Toe ±.13° to ±.50° Required: 1 shim per wheel/per angle changed APPLICATIONS Audi FWD: 2000 - 06 TT Volkswagen: 1998 - 10 Beetle 1999 - 06 Golf (Except R32) 1999 - 06 GTI 1999 - 05 Jetta (Beam Rear Axle) CAUTION: Check brake & rotor clearance for binding. 75970 spacers g p (page 118) maybe required.

brake sensor ring, bearing, seal and hub assembly as one unit. 71500 SHIMSET Includes 16 shims/2 of each size and 87530 wrench.

TOE Part No. Change 71520 ± .13° 71521 ± .25° 71522 ± .38° 71523 ± .50° CAMBER 71530 +.50° 71531 +1.00° 71532 -.50° 71533 -1.00°

NOTE: When installing these shims we recommended that you use our VW Shim Wrench (#87530 pg. 170) to assist in removing the rear hub.

87530 - Wrench

71600 SERIES

TOYOTA SIENNA REAR CAMBER AND TOE SHIMS

Rear Adjustment range: Camber ±.25° and ±.50° Toe ±.10° to ±.50° Required: 1 or 2 shims per wheel

These full contact shims correct camber and/or toe on both AWD and FWD Toyota Siennas. Combination adjust ments, or changes up to 1° may be made by stacking up to 2 shims per side.

TOE Part No. Change 71621 ± .10° 71622 ± .20° 71623 ± .30° 71624 ± .40° 71625 ± .50° CAMBER 71631 ± .25° 71632 ± .50°

APPLICATIONS Toyota AWD/FWD: 2011- 20 Sienna 71600 SHIMSET - Includes 14 shims/2 of each size.

71700 SERIES

CHRYSLER MINI-VAN SHIMS

Rear Adjustment range: Camber ±1.00°/Toe ±.10° to ±.80° Required: 1 shim per wheel/ per angle changed APPLICATIONS Chrysler 1996 - 16 Town & Country FWD: 2000 - 03 Voyager Dodge 1996 - 07 Caravan FWD: 1996 - 20 Grand Caravan Ram 2012 - 15 Tradesman FWD: Conversion Van Nissan: 2007 -12 Sentra Plymouth FWD: 1996 - 01 Voyager Volkswagen FWD: 2009 - 14 Routan Rear Adjustment range: Camber ±.25°, ±.50°, ±1.00° Toe ±.10 to ±.50° Required: 1 or 2 shims per wheel APPLICATIONS Nissan: 2011 - 17 Juke 2011 - 24 Leaf

For camber and toe change, use our mini-van shims that allow for quick and easy changes in increments of: toe .10° and camber .25°. 71700 SHIMSET - Includes 20 shims/2 of each size F m a t 7

CAMBER Degree Part No. of Change

Degree of Change ± .10° [.05” (1/16”)] ± .20° [.10” (1/8”)] ± .30° [.15” (5/32”)]

Degree of Change ± .40° [.20” (3/16”)] ± .50° [.25” (1/4”)] ± .80° [.40” (3/8”)]

TOE

± .25° (1/4°) ± .50° (1/2°) ± .75° (3/4°) ± 1.00° (1°)

Part No. 71720 71721 71722

Part No. 71723 71724 71725

71730 71731 71732 71733

71715

NISSAN HUB SHIM HARDWARE

Use these longer bolts on the rear axle Nissan Leaf and Juke when djusting the alignment with the 71700 series shims. The factory bolts often aren’t long nough when camber and toe e adjusted using SPC’s axle ms, these longer bolts ensure engagement on the rear per kit, only one kit is needed Use these lo for theN ad t f e are shim

proper thread hubs. Sold 8 p per vehicle.

Call for your nearest distributor, product info or www.specprod.com 1-800-525-6505 Technical Assistance • In the USA and Canada 106