2022-2023 Total Wheel Alignment Sourcebook

Parts

71030 SERIES 71050 SERIES

GM REAR TOE AND CAMBER SHIMS

Rear Adjustment range: Camber ±1.00°/Toe ±1.00° Required: 1 or 2 per wheel 71030 Series APPLICATIONS Buick: 2012 - 17 Verano Cadillac: 2014 - 16 ELR Chevrolet: 2011 - 19 Cruze 2011 & Up Volt 71050 Series APPLICATIONS Buick FWD: 2013 - 23 Encore Chevrolet FWD: 2012 - 20 Sonic 2015 - 22 Trax

Make rear wheel alignment changes on these twist beam axles with SPC’s stackable fixed change shims. Change camber in ±.25° increments and toe in ±.10° increments. Combine a toe shim with a camber shim to get the exact change required. Stack up to two shims for maximum change.

71030 SERIES

Change

CAMBER Change

TOE 71031 71032 71033 71034 71035 TOE 71051 71052 71053 71054 71055

± .10° ± .20° ± .30° ± .40° ± .50° ± .10° ± .20° ± .30° ± .40° ± .50°

71041 71042 71045 71046

+.25° +.50° -.25° -.50°

71030 SHIM SET Includes 18 shims/ 2 each of 71031-71035 and 71041-46

71050 SHIM SET Includes 18 shims/ 2 each of 71051-71055 and 71061-71066

71050 SERIES

Change

CAMBER Change

71061 71062 71065 71066

+.25° +.50° -.25° -.50°

71070 SERIES

RIO/ACCENT REAR SHIMS

Rear Adjustment range: Toe ±.50° Required: 1 per wheel APPLICATIONS Hyundai:

The twist beam axle on the rear of the Kia Rio a Hyundai Accent does no give you any method to adjust toe. Correct toe and thrust angle issues to improve drivability and increase tire life with these full contact shims.

TOE Part No. Change 71071 ± .13° 71072 ± .25° 71073 ± .38° * 71074 ± .50° * 71070 SHIM SET Includes 8 shims/2 each size

nd t

2012 - 17 Accent

Kia: 2012 - 17 Rio CAUTION: Do NOT stack this shim. * Includes brake caliper shim

71500 SERIES

VW/AUDI REAR SHIMS With these shims you can correct rear camber and toe on newer Volkswagens and Audis. By combining the shims (two may be used on each wheel) you can get ±.50° to ±1.0° camber change and up to ±.50° toe change. Our wrench (# 87530 ) is a must

Rear Adjustment range: Camber ±.50° to ±1.00°/ Toe ±.13° to ±.50° Required: 1 shim per wheel/per angle changed APPLICATIONS Audi FWD: 2000 - 06 TT Volkswagen: 1998 - 10 Beetle 1999 - 06 Golf (Except R32) 1999 - 06 GTI 1999 - 05 Jetta (Beam Rear Axle) CAUTION: Check brake & rotor clearance for binding. 75970 spacers (page 118) maybe required.

TOE Part No. Change 71520 ± .13° 71521 ± .25° 71522 ± .38° 71523 ± .50° CAMBER 71530 +.50° 71531 +1.00° 71532 -.50° 71533 -1.00°

when installing these shims. It allows you to remove the

brake sensor ring, bearing, seal and hub assembly as one unit. 71500 SHIM SET Includes 16 shims/2 of each size and 87530 wrench.

NOTE: When installing these shims we recommended that you use our VW Shim Wrench (#87530 pg. 170) to assist in removing the rear hub.

87530 - Wrench

71600 SERIES

TOYOTA SIENNA REAR CAMBER AND TOE SHIMS

Rear Adjustment range: Camber ±.25° and ±.50° Toe ±.10° to ±.50° Required: 1 or 2 shims per wheel

These full contact shims correct camber and/or toe on both AWD and FWD Toyota Siennas. Combination adjust ments, or changes up to 1° may be made by stacking up to 2 shims per side.

TOE Part No. Change 71621 ± .10° 71622 ± .20° 71623 ± .30° 71624 ± .40° 71625 ± .50° CAMBER 71631 ± .25° 71632 ± .50°

APPLICATIONS Toyota AWD/FWD: 2011- 20 Sienna 71600 SHIM SET - Includes 14 shims/2 of each size.

Call for your nearest distributor, product info or 1-800-525-6505 www.specprod.com Technical Assistance • In the USA and Canada

101