2019 Product Catalog

NEW!

Pump Motors Vertical Hollow Shaft Motors

Pump

Motors

Product specification

Feature

Standard

Feature

Standard

General

Mechanical Characteristics

Motor Type Enclosure

Three Phase Induction Motors

Frame sizes

210TP through 449TP

Water Protected Type 1

Frame construction

Cast iron

Washguard Motors

Power Output

7.5HP up to 300HP

Mounting

Vertical round, P-Base

P-base material Canopy material

Cast iron

2 Pole (3600RPM) up to 100HP and 4 Pole (1800RPM) through 300HP

Speeds

Steel

Design Standard

NEMA MG1

Conduit box material

Cast iron

Regulatory Markings

UL C-US; CE Mark

Meet or exceed NEC NFPA70; (same as NEMA MG-1 & UL1004-1)

Conduit box compartment volume

ODP Enclosure

ODP Enclosure Enamel Paint

Chemical Resistant Paint Cast Iron Conduit Box

Conduit box hole (customer entry)

NPT IP23

Stamped Steel Conduit Box

IP Code

Agricultural

Gasket between frame and C-box base

Electrical Characteristics

Duty Motors

Gaskets

60/50 (50 Hz @ next lower HP, 1.15 SF) 230/460v through 405 frame, 460v 440 frame and larger. "190/380V next lower HP for baseline 230/460v 60Hz motor 380V next lower hp for baseline 460v 60Hz motor" 1.15 S.F. capability @ 60Hz and 50Hz "12 leads Y-start/D-run for 230/460v 213-405 frame (PWS on 230v) 6 lead PWS/Y-start/D-run for 460v in 444 frame and larger"

Frequency

Conduit box mounting/assembly

4 bolt, diagonally split

Ability to rotate conduit box in 90 deg increments or accessibility of incoming power from 12:00, 3:00, 6:00 or 9:00 positions

Standard voltage rating 60Hz

Conduit Box Rotation

Standard voltage rating 50Hz

Grounding provision

Inside C-Box

HVAC / Fan Motors

Insulation Class Insulation Type

Class F

Service Factor

Inverter capable

"Angular contact back to back up to frame size 405 Angular contact tanden for frame sizes 444 and larger" See maximum down thrust values, based on bearing life 8760 hrs, on table 1. Maximum 30% of downthrust capability "Exxon Polyrex EM grease for motors 280 frame and smaller. 320 frame and larger uses oil for upper bearing (ISO R32 recommended) and Exxon Polyrex EM grease for lower bearing" No (See options) Single row ball bearing

Lead configuration

Upper Bearing (Thrust Bearing)

Lead terminations

Loose leads, ring terminals

Lower Bearing

Lead length

6"

Special Voltage Motors

Downthrust

Efficiency

NEMA Premium @60Hz, full load

NEMA Design

Design B

Full Load MAXIMUMTemperature Rise

Upthrust

80C rise at 1.0 load

Insulated bearing

Service Factor

1.15 S.F. capability @ 60Hz and 50Hz

Duty Cycle

Continuous

Ambient Operating Temperature rating

-20 to 40 degree C max

Upper Bearing Lubrication

Definite

Protection Devices

None (See options)

Purpose Motors Brake Motors IEC Motors DC Motors

Altitude rating

0-3300 feet (0-1000 meters) 3:1 VT with non-reverse ratchet

Lower Bearing Lubrication Regreasing provisions Grease and Oil drain type and location

Exxon Polyrex EM grease

Inverter capability

Plugged holes

Continuous overspeed capability

60Hz base speed Standard feature None (See options)

Lubrication holes in each bracket, holes are plugged Moisture drain hole in P-base and left open.

Winding space heaters

Winding temperature sensors

Modification capabilities

Moisture drain type and location

Alternative sizes available as modification

P-Base Flanges

Bearing current mitigation

None (See options) V-ring rubber shaft seal

Shaft seal / slinger Nameplate material

Steady Bushings kits

Available Available

Stainless steel

Coupling Kits Ground ring

Stamped, metal embossed or laser etched. Unified Thread Standard (inches) Vertical, minimum 5.0 NEMA safety factor Per NEMA (0.15 in/s maximum velocity)

Available as a modification Available as a modification

Nameplate Printing Method

Temperature Sensors

Hardware - Main

Rigid coupling (no NRR) available as a modification

Coupling locking options

Lifting provisions

Vibration Limits

Sound Limits

per NEMA MG-1

132